Power System Protection

Interpret how relays and breakers detect and isolate grid faults.

Follow the trip path from instrument transformer to relay to breaker. Compare how utilities protect feeders, transmission lines, transformers and buses.

Request this course Email about this courseView course content
One full day8:00 a.m.–5:00 p.m. with eight hours of instruction
Technical courseRelays, breakers and protection schemes
Applied exercisesTime-current curves and fault-event analysis

Course overview

Learn how utilities recognize abnormal conditions, isolate faulted equipment and coordinate protection across transmission and distribution. Work from one-lines, time-current curves and example event records to connect relay actions with what happens on the grid.

Learning objectives

  • Explain common fault types and identify primary and backup protection zones.
  • Trace the measurement, decision and trip sequence.
  • Read time-current curves and discuss coordination trade-offs.
  • Compare feeder, transmission line, transformer and bus protection.

Who should attend

Utility engineers, relay and substation technicians, system operators, distribution planners and project managers who work with protection systems.

The course also suits utility partners who need to understand protection drawings, equipment functions and outage investigations.

From fault measurement to isolation

Detect the fault

Measure current and voltage.

Current and voltage measurements give the relay information about the fault.

Decide what should trip

Identify the affected protection zone.

Protection logic interprets the measurements and determines whether to trip.

Isolate the fault

Open the right breakers.

The assigned breaker opens to isolate the faulted section.

Course content

Compare protection schemes and use example records to explain which devices should operate and why.

Faults and protection objectives

  • Compare phase-to-ground, phase-to-phase and three-phase faults, including temporary and sustained faults.
  • Explain how source strength, grounding and line impedance affect available fault current and relay sensitivity.
  • Use a one-line diagram to identify protection zones, zone overlap, primary protection and backup protection. Compare selectivity, speed, sensitivity and dependability.

Instrument transformers, relays and breakers

  • Trace the trip path from current and voltage transformers through relay logic, station DC power and breaker trip coils.
  • Recognize CT ratio, polarity, burden and saturation as factors in relay measurement. Distinguish pickup, timing, trip and alarm.
  • Compare circuit breakers, fuses, reclosers and sectionalizers by their roles, ratings and interrupting capabilities.

Distribution feeder protection and coordination

  • Read time-current curves and compare fuse-to-fuse, fuse-to-recloser and relay-to-recloser coordination.
  • Compare fuse-saving and fuse-blowing approaches, overhead and underground practices, and how reclosing affects temporary faults and outage exposure.
  • Discuss load encroachment, cold-load pickup, minimum fault current, distributed generation and reverse power flow as coordination constraints.

Transmission line protection

  • Compare directional overcurrent, distance and line differential protection. Explain apparent impedance, relay reach and local versus remote backup.
  • Describe how communications-assisted schemes exchange information between line terminals. Discuss the effects of channel loss and the purpose of breaker-failure protection.
  • Explain when automatic reclosing may be appropriate and why utilities review it alongside system conditions and operating practices.

Transformer and bus protection

  • Compare transformer and bus differential protection with overcurrent backup. Identify factors that can create apparent differential current during normal operation or external faults.
  • Explain the purpose of transformer inrush restraint and how CT saturation can affect differential security.
  • Trace the expected trip boundaries for a transformer or bus fault on a substation one-line.

Testing, event review and coordination exercise

  • Identify what commissioning and periodic testing confirm about measurement, relay logic, communication and the trip path.
  • Read an illustrative sequence-of-events record and relay event report to distinguish the initiating fault from protective actions.
  • Compare upstream and downstream device responses in a sample feeder case and explain backup operation if the primary device fails.

Course recap & participant questions

Review the fault-clearing case, explain the expected primary and backup responses, and discuss how the concepts apply to your team’s equipment and operating practices.

Agenda

8:00 a.m.–5:00 p.m., including eight hours of instruction, two 15-minute breaks and a 30-minute lunch.

Morning

  • 8:00–8:45 a.m.
    Fault types and protection zones
  • 8:45–10:00 a.m.
    Fault current and the trip path
  • 10:00–10:15 a.m.
    Break
  • 10:15–11:15 a.m.
    Distribution protection devices
  • 11:15 a.m.–12:15 p.m.
    Coordination exercise
  • 12:15–12:45 p.m.
    Lunch

Afternoon

  • 12:45–1:45 p.m.
    Transmission protection and reclosing
  • 1:45–2:45 p.m.
    Transformer, bus, and backup protection
  • 2:45–3:00 p.m.
    Break
  • 3:00–4:00 p.m.
    Testing and fault-clearing case
  • 4:00–4:35 p.m.
    Case review and backup response
  • 4:35–5:00 p.m.
    Recap and questions

Planning & FAQs

How is pricing structured?

We quote one course fee for your organization, with no per-person charge. Share your preferred dates and delivery format when requesting a quote.

What background is helpful?

Familiarity with basic AC power and utility one-line diagrams helps. The course introduces protection terminology before the case exercises.

Can we focus on transmission or distribution?

Share the equipment and protection challenges your team works with so we can discuss which examples to emphasize.

Will we work through relay settings?

We use illustrative curves and event records to explain protection decisions. Site-specific settings require system data and an engineering review.

How do we arrange training?

Send your audience, group size, priorities, preferred format and dates so we can discuss delivery.

Straightforward group pricing

One course fee. Your whole team.

Your organization pays one course fee with unlimited attendees at no extra cost.

Live online training

$7,000

Typical fee for a one-day course delivered live online to your team.

In-person training

$9,000

Typical fee for a one-day course at your organization.

Request a proposal to confirm the fee, agenda, and delivery arrangements for your training.

Request quote

Bring power system protection training to your team.

Tell us which protection systems your team works with and what you want participants to understand about relays, coordination or fault response.

Request this course Email about this course